It is now possible to change springs at the track without affecting the corner weights or percentages! Simply secure this unit to the hub via the wheel studs, turn it on, and lower the vehicle to the ground. Record the reading from the digital display, then make the spring change. Adjust the weight jack bolt or coil over nut until the digital display matches the starting value. Works great on asphalt or unimproved surfaces.

Includes a 5x5 Hub adapter

Dual Display for easy viewing of all pressures.

Includes Case

Intercomp's Race Car Management Software organizes information for easy future interpretation and is the key to consistent on-track success. This program provides the ability to systematically record and retrieve all-important information, helping your team be more successful from week to week and track to track.

Primary Screens:

Record and Organize Chassis Data Like Never Before!

Additionally, the software enables direct interface with these Intercomp scale systems and products:

Low Profile ramp for 2.5"/64mm scale pads. 15"x15"/380mm x 380mm, lightweight, aluminum design complements all 2.5" profile scale systems.

High quality scale cart with wheels. Strong and lightweight.

Carries Four Pads, Cables, and Controller.

Transports 2.5" or 4" scale pads.

For 2.5" profile, pads, cabling, & control.

ATA300 approved with 12 gauge corners, military spec latches, & handles.

For 4" profile, pads, cabling, & control.

ATA300 approved with 12 gauge corners, military spec latches, & handles.

Take all the guess work out of leveling weigh pads, roll off pads, or drive-on setup racks. Laser sighting with virtually an unlimited range. Can be used with all scale systems.

CNC machined billet aluminum housing with easy-to-read bubble display. Measure -6 to +6 degrees of camber.

INCLUDES: Magnetic Adapter & Case

CNC machined billet aluminum housing with easy-to-read bubble display. Measure -6 to +6 degrees of camber.

INCLUDES: 5/8" Adapter & Case

NiCad rechargeable battery stick.

Models SWII, SWI, SW88, & SW-Kart Scales require one battery stick.

All other scale models require two battery sticks.

Foam-lined carrying case for equipment storage.

Dimensions: 13.5"x10"x3.75"/340mm x 250mm x 95mm

Shocks are the most important part of your vehicles suspension and need to be maintained just like any other mechanical device that has valves, seals and oil. New and used shocks should be tested for performance characteristics.

Dynamometer Specs:

16mm - 1.5

SET OF 2

10" Down Ramps enable "drive-over" capability on our Scale Setup Racks.

The industry's easiest to use and most compact lap timer at just 4"x2.5"x0.8"/100x6x20mm.

On-Board display unit only.

NOT a complete timing system.

In-field transmitter unit only.

NOT a complete timing system.

GREAT FOR SNOWMOBILES, MOTORCYCLES, ATV's, AND RACE CARS!

A "must have" for optimum shock management. This unit allows quick and exact pressure settings to 300 PSI in 0.5 increments and is compatible with most any brand of shock. The thumb-operated bleeder eliminates the need to "crack" the seal to achieve desired pressure and the indicator is positioned at the end of a swivel-mounted hose to provide optimum visibility at any angle, whether the shock is in the vise or on the car.

Comes standard with "schrader" valve adapter for Penske-style valve.

Needle valve adapter for Ohlins-style valve is available

Includes Case

Needle valve adapter for Intercomp's Shock Pressure Gauge.

Screws into standard "Schrader" on the gauge to suit Ohlins-style shocks.

(Factory Certified)

This ultra quick, high accuracy, digital gauge is the choice of professionals in all types of motorsports.

Includes Case

CNC machined billet aluminum housing with easy-to-read bubble display. Measure -6 to +6 degrees of camber.

INCLUDES: Case

SET OF 4

For any 15"x15"/380mm x 380mm, 2.5"/64mm or 4"/100mm profile, scale pad. High quality, steel construction with a powder coat finish.

Now displays to one hundredth of a percent!

Featuring

• 15"x15"x4" (381x381x100mm) Billet Pads
• Quick Disconnect Indicator with Case
• Quick Disconnect Cables

Replacement chuck for digital air gauges.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Includes a high-quality, thumb operated bleeder and swivel nozzel on a 17" Goodyear Hose. High visibility with major and minor graduation marks.

Intercomp's "Fill, Bleed, and Read" Air Gauges attach directly to your air or nitrogen hose and have transformed a tedious process into one smooth and easy operation. Standard features include a high quality, 4" pressure gauge with rubber protective boot, a 22" Goodyear Hose with a high quality swivel nozzle, and an industrial-grade bleeder valve. The air chuck never leaves the valve stem.

Intercomp's "Fill, Bleed, and Read" Air Gauges attach directly to your air or nitrogen hose and have transformed a tedious process into one smooth and easy operation. Standard features include a high quality, 4" pressure gauge with rubber protective boot, a 22" Goodyear Hose with a high quality swivel nozzle, and an industrial-grade bleeder valve. The air chuck never leaves the valve stem.

Intercomp's "Fill, Bleed, and Read" Air Gauges attach directly to your air or nitrogen hose and have transformed a tedious process into one smooth and easy operation. Standard features include a high quality, 4" pressure gauge with rubber protective boot, a 22" Goodyear Hose with a high quality swivel nozzle, and an industrial-grade bleeder valve. The air chuck never leaves the valve stem.

Intercomp's "Fill, Bleed, and Read" Air Gauges attach directly to your air or nitrogen hose and have transformed a tedious process into one smooth and easy operation. Standard features include a high quality, 4" pressure gauge with rubber protective boot, a 22" Goodyear Hose with a high quality swivel nozzle, and an industrial-grade bleeder valve. The air chuck never leaves the valve stem.

Intercomp's "Fill, Bleed, and Read" Air Gauges attach directly to your air or nitrogen hose and have transformed a tedious process into one smooth and easy operation. Standard features include a high quality, 4" pressure gauge with rubber protective boot, a 22" Goodyear Hose with a high quality swivel nozzle, and an industrial-grade bleeder valve. The air chuck never leaves the valve stem.

This digital unit delivers unsurpassed accuracy via a digital controller, accomodating PSI, BAR, & Kg/Cm2 units of measure.

Industry's Highest Accuracy Bubble Gauge!  CNC-machined, billet, aluminum housing with easy-to-read bubble display. Measures -6 to +6 degrees of camber and -8 to +8 degrees of caster with 0.25 degree accuracy.

INCLUDES: Magnetic Adapter & Case

Industry's Highest Accuracy Bubble Gauge!  CNC-machined, billet, aluminum housing with easy-to-read bubble display. Measures -6 to +6 degrees of camber and -8 to +8 degrees of caster with 0.25 degree accuracy.

INCLUDES: Case

Can be used with most brands of caster/camber gauges.

GM .750 - 20 UNEF

Can be used with most brands of caster/camber gauges.

Big Ford .813 - 20 UNEF

Can be used with most brands of caster/camber gauges.

Wide-5 1.813 - 16 UN

Can be used with most brands of caster/camber gauges.

SCP .844 - 20 UNF

East-to-use, high performance, tire system will vacuum and fill four tires simultaneously through a desiccant monitor. This system is compact and mounted on a transportable hand cart.

GREAT FOR SNOWMOBILES, MOTORCYCLES, ATV's, AND RACE CARS!

A "must have" for optimum shock management. Measures pressure in PSI and BAR with a pressure range up to 300 PSI and 0-20 BAR and is compatible with most any brand of shock. Liquid Filled Gauge.

New Billet Digital Depth Gauge measures depth in 0.0005" and 0.0127mm increments with a range of 0-.25"/6.35mm.

Includes: Case

Can be used with most brands of caster/camber gauges.

Magnetic 3.5"OD - 1.55"ID

Can be used with most brands of caster/camber gauges.

Toyota/Legends 19mm - 1.5

Can be used with most brands of caster/camber gauges.

US Kart .625 - 18 UNF

Can be used with most brands of caster/camber gauges.

Small Ford .750 - 16 UNF

Can be used with most brands of caster/camber gauges.

Kart .50 - 13UNC

Can be used with most brands of caster/camber gauges.

Kart-Metric 14/17mm - 1.5

Can be used with most brands of caster/camber gauges.

BLANK

Commercial grade clamp fits most any size rim. Rugged design with two types of clamps guarentees a secure fit.

Use with our Digital Caster/Camber Gauge or Bubble Caster/Camber Gauge, with a magnetic adapter, to complement this front end tool.

Perfect for repair shops and vehicles with expensive aluminum wheels!

Commercial grade clamp fits most any size rim. Rugged design with two types of clamps guarentees a secure fit.

Use with our Digital Caster/Camber Gauge or Bubble Caster/Camber Gauge, with a magnetic adapter, to complement this front end tool.

Perfect for repair shops and vehicles with expensive aluminum wheels!

High capacity, portable, scale system is ideal for wind tunnel testing, and weighing trailers, tractors, coaches, mobile homes, and other large wheeled vehicles. This system has a capacity of 20,000lb/10,000 kg and eliminates the need to guess your corner weights.

The industry's first tester that can accuratly rate a torsion bar.

Digitally measures twist of torsion bars to +/-25 degrees and measure force at a specific degree of twist up to 2,000 ft lbs. Works with bars 18"/457mm-30"/762mm in length and splines 7/8"/ to 2" in diameter.

Custom splined adapters available.

1 set of adapters included.  Specify spline size when ordering.

Tire & Brake temperatures tell the story! Tire & Brake temperatures are the best indicator of how a chassis is handling, but it is critical that this key information be gathered as rapidly as possible.

Intercomp's proven digital tire/brake pyrometer. Voted the most accurate in the industry!

Includes tire probe and case

Optional tire probe for Intercomp's Pyrometer

Optional brake probe for Intercomp's Pyrometer

The surface of a tire becomes harder with every heat cycle and even new tires of the same compound can vary a great deal in hardness. If a tire is too soft for the track, it will overheat and may not last the entire race, but if it is too hard, it will not get up to the optimum temperature and traction will be sacrificed. Intercomp's Tire Durometer enables you to make the correct tire selections for any track.

Recommended by the leading spring manufacturers in the world. Portable, digital force, travel indication, and 9 Volt battery powered. Large 0.5" display, knurled pressure relief knob and peak hold feature. Stop guessing, now you can pinpoint spring rates to determine high accuracy splits and enhance chassis tuning.

Quick, single pin, vertical adjustment allows almost any spring to be rated. Handles flat, coil-over springs up to 6"/150mm in diameter by 18"/457mm high, optionally to 30"/760 mm. Readout in 1lb/kg increments.

Tire Durometer: The surface of a tire becomes harder with every heat cycle, and even new tires of the same compound can vary a great deal in hardness. If a tire is too soft for the track, it will overheat and may not last the entire race. If it is too hard, it will not get up to the optimum temperature and traction will have to be sacrificed. Intercomp's Tire Durometer enables you to make the correct tire selections for any track.

Tire Tread Depth Gauge:  Measures tire wear in 1mm and 1/32" increments.  Aluminum Construction.

Includes cases for both gauges.

Foam-lined carrying case for equipment storage.

Dimensions: 19"x14"x5.5"/483mm x 356mm x 140mm

Lap Timer to Computer Cable.

Recommended by the leading spring manufacturers in the world. Portable, digital force, travel indication, and 9 Volt battery powered. Large 0.5" display, knurled pressure relief knob and peak hold feature. Stop guessing, now you can pinpoint spring rates to determine high accuracy splits and enhance chassis tuning.

Quick, single pin, vertical adjustment allows almost any spring to be rated. Handles flat, coil-over springs up to 6"/150mm in diameter by 18"/457mm high, optionally to 30"/760 mm. Readout in 1lb/kg increments.

Quick and easy retrofit from Coil Spring to Fork Spring Tester. Intercomp's Fork Spring Retrofit Kit is designed to work with Intercomp's Digital Coil Spring Testers. Accommodates up to 2"/48mm diameter and 36"/917mm long fork springs. Readout on 0.1lb/kg increments. Kit includes a load cell, digital indicator and fork spring guide tube.

Portable, digital force, & travel indication, battery powered (9v) with 300 hour battery life. High accuracy & repeatability. Peak hold feature saves maximum reading. Pushbutton On/Off and Zero makes this unit user friendly. Excellent for valve, clutch, shock, & pressure relief springs up to 2" (50mm) in diameter. Readout in .2lb/kg increments.

Digital tester is ideal for checking valve seat pressure on an assembled engine. Precision 5.0lb/kg increments can detect a fatigued, broken, or misaligned spring. Simple method to maintain a valve train. Can be used on most wedge engines with rocker shafts and aluminum rockers and the brass contact prevents rocker damage. Four positional adjustments and peak hold feature enable getting into hard to reach areas.

The first bump steer gauge that provides digital travel indication. Two dial indicators, a sturdy anti-slip "T" base with leveling feet and a leveling bubble allows for use with car on a jack stand and can be used with a standard floor jack or bottle jack.

No pivot or heim joints to induce error. Standard hub plate works with most 5-bolt hub patterns from 4.5" to 5".

Two dial indicators, a sturdy anti-slip "T" base with leveling feet and a leveling bubble allows for use with car on a jack stand. No pivot or heim joints to induce error. Standard hub plate works with most 5-bolt hub patterns from 4.5" to 5". Our gauge can be used with a standard floor jack or bottle jack.

Aluminum hub plate with no factory pre-drilled holes for your customization. Designed for vehicles with unusual hub bolt patterns.

The user is required to drill the necessary holes to accommodate their particular application.

Aluminum hub plate with factory pre-drilled holes for Legends.

Designed for vehicles with the Legends bolt patterns.

Aluminum hub plate designed for vehicles with the Viper bolt patterns.

SET OF 2

Easy-to-read, CNC machined numbers can indicate from -35 to +35 degrees in 0.5 degree increments.

Total capacity of 2,000lbs/909kg with three levels of metal roller bearings and high-friction top surface to eliminate tire slippage.  No plastic rollers or bearings!  Car can be zeroed in place.

Constructed from lightweight, aerospace grade aluminum.

Mechanical Turn Plates can be upgraded to digital readout.

SET OF 2

Maintain proper weight distribution by keeping the rear level with the front turnplates. Lightweight, aerospace grade aluminum construction!

SET OF 2

Two high strength, lightweight, aluminum plates for quick, easy, and accurate toe measurements.

Intercomp's, bolt-on, front toe plates allow for quick and easy setting of toe and also provides a means of obtaining other nominal measurements for quick "post-crash" analysis.

Will accomodate Standard US hubs 3 on 2.5" bolt circle (1/4 and 5/16 stud), and Standard International sizes 3 on 58 mm and 3 on 67 mm bolt circle.

The key to setup consistency is the baseline. When incorporating the front toe plates with Intercomp's bolt-on rear alignment plates, a first class, four-plate, alignment and setup system is created.

This system provides EXACT baseline recall for setting toe, four wheel squareness, and wheel offsets. This system accomodates standard US hubs 3 on 2.5" bolt circle (1/4 & 5/16 stud), and Standard International sizes 3 on 58mm and 3 on 67mm bolt circle.

0.5" Wide x 10' Long

Indicates in inches/feet.

An economical tool to verify A-frame and shock angles, as well as pinion, upper link, and trailing arm angles.

The magnetic base enables you to verify angles in tight areas. Excellent for measuring spoiler angles. Ball bearing design eliminates hangups.

The industry's first tester that can accuratly rate a torsion bar.

Digitally measures twist of torsion bars to +/-25 degrees and measure force at a specific degree of twist up to 2,000 ft lbs. Works with bars 18"/457mm-48"/1,249mm in length and splines 7/8"/ to 2" in diameter.

Custom splined adapters available.

1 set of adapters included.  Specify spline size when ordering.

This tester will digitally determine the spring rate of Leaf Springs up to 2,000lbs in 1lb increments and can measure up to four inches of travel with an electronic digital indicator.

Leaf springs are rated just as they are positioned in a car, with one end fixed and free at the two other points. Tests leaf springs up to 58"/1473mm in length.

Dial in your tire spring rate to optimize handling characteristics. Identifying sidewall spring rate adds another dimension to your chassis tuning abilities.

Reduces variability in tires by matching the spring rates. Dial in your tire spring rate to optimize handling characteristics. Identifying sidewall spring rate adds another dimension to your chassis tuning abilities.

Displays relative humidity (%RH) & temperature (Fahrenheit or Celsius) within a tire. Using the included valve stem adapter, simply place the unit on the valve stem and allow air to pass by the sensor to obtain a reading.

Includes: Meter and Valve Stem Adapter.

Compact sound level meter with digital display. Excellent for monitoring noise levels to comply with zoning regulations.

Includes: Carrying Case

Air density is the single-most important engine tuning parameter in all forms of professional motorsports because it is derived from air temperature, barometric pressure, and humidity.

This tool will allow you to properly tune your engine for optimum performance.

Carrying case and instructions with recommendations are included.

THIS ITEM CANNOT SHIP VIA AIR FREIGHT.  Must ship ground services only.

Ultra lightweight 10"x10"/255mm x 255mm platform scale is designed to weigh fuel dump cans. Measure quickly between pit stops on race day.

When your torque wrench is set at 35 ft lb, is it really clicking at 35 ft lb?

Peak hold feature saves the maximum reading. The range of the digital display is 200 ft lb in 1.0 increments. Pushbutton conversion from ft lb to in lb and Nm. Accommodates a 1/2" torque wrench.

NTEP Class III Certified Ideal for weighing engines, dump cans in the pit, or for general chassis fabrication.

Intercomp's CS750 is the premier choice with it's large, easy-to-read, 1", LCD display, 20-bit A/D converter, providing the highest accuracy available, and Infared Remote for operating at a distance. 

View scale readings from afar with Intercomp's SA2000 Remote Display!

The number one choice of top sanctioning bodies for publicly displaying scale readings in the inspection area. Displaying Total Weight and/or a certain regulated percentage (such as Left% or Front%) doesn't give away a team's setup, but it totally eliminates the possibility of inspector "favoritism" - allowing each team to play by the same rules. It also gives technical inspectors more leverage to enforce weight violations!

Set of Four For SW500, SW520, SW650R1, and SW777 Scale Systems.

Includes One Each of the Red, Green, Black, and White Cables.

Small patch with embroidered Intercomp logo for driver/crew uniforms.

Package of 12

2"x10"/51mm x 254mm decal with Intercomp logo.

Black background with white text.

Cotton golf shirt with Intercomp Racing logo embroidered on chest.

Available in small, medium, large, XL, 2XL, and 3XL.

High quality two-tone denim jacket with blue body and offsetting tan sleeves. Multi-colored Intercomp Racing logo is embroidered on the back.

Available in Small, Medium, Large, X-Large, and XX-Large.

It is now possible to change springs at the track without affecting the corner weights or percentages! Simply secure this unit to the hub via the wheel studs, turn it on, and lower the vehicle to the ground. Record the reading from the digital display, then make the spring change. Adjust the weight jack bolt or coil over nut until the digital display matches the starting value. Works great on asphalt or unimproved surfaces.

Includes a Wide-5 Hub adapter

Intercomp's handheld, dual-screen, Lap Timer allows you to simultaneously record 100 lap times of four (4) vehicles.

Standard Features include:

Intercomp's "Fill, Bleed, and Read" Air Gauges attach directly to your air or nitrogen hose and have transformed a tedious process into one smooth and easy operation. Standard features include a high quality, 4" pressure gauge with rubber protective boot, a 22" Goodyear Hose with a high quality swivel nozzle, and an industrial-grade bleeder valve.

Intercomp's "Fill, Bleed, and Read" Air Gauges attach directly to your air or nitrogen hose and have transformed a tedious process into one smooth and easy operation. Standard features include a high quality, 4" pressure gauge with rubber protective boot, a 22" Goodyear Hose with a high quality swivel nozzle, and an industrial-grade bleeder valve.

Industry's Highest Accuracy Bubble Gauge!  CNC-machined, billet, aluminum housing with easy-to-read bubble display. Measures -6 to +6 degrees of camber and -8 to +8 degrees of caster with 0.25 degree accuracy.

INCLUDES: Wide-5 Adapter & Case

Industry's Highest Accuracy Bubble Gauge!  CNC-machined, billet, aluminum housing with easy-to-read bubble display. Measures -6 to +6 degrees of camber and -8 to +8 degrees of caster with 0.25 degree accuracy.

INCLUDES: GM Adapter & Case

Industry's only fully Digital Caster/Camber Gauge!

Indicates to 1/10 of a degree and has a +/- 20 degree caster/camber reading. Up to 10 times greater accuracy than traditional competitor's bubble gauges. Standard 9-volt battery gives up to 100 hours of operation. Lightweight, aluminum design, with auto shutoff and inclinometer mode for pinion and strut angles.

Standard features include

INCLUDES: Magnetic Adapter and Case

Industry's only fully Digital Caster/Camber Gauge!

Indicates to 1/10 of a degree and has a +/- 20 degree caster/camber reading. Up to 10 times greater accuracy than traditional competitor's bubble gauges. Standard 9-volt battery gives up to 100 hours of operation. Lightweight, aluminum design, with auto shutoff and inclinometer mode for pinion and strut angles.

Standard features include

Industry's only fully Digital Caster/Camber Gauge!

Indicates to 1/10 of a degree and has a +/- 20 degree caster/camber reading. Up to 10 times greater accuracy than traditional competitor's bubble gauges. Standard 9-volt battery gives up to 100 hours of operation. Lightweight, aluminum design, with auto shutoff and inclinometer mode for pinion and strut angles.

Standard features include

Can be used with most brands of caster/camber gauges.

Magnetic/NASCAR 2.25"OD - 1.55"ID

Displays current and maximum reads.

Ideal for checking temperature of tires, brake rotors, radiator, header tubes, track, hoses, fuel, driver compartment, and bearings.

Handheld, battery-powered, non-contact, temperature guns are compact and easy-to-use. Delivers a fast response time in 500 ms.

For SW500, SW520, SW650R1, and SW777 Scale Systems.

Includes One Red Cable.

Place fixture on the wheel rim to take caster/camber measurements. Works on 13" - 17" wheels.

Use with either our digital or bubble caster camber gauges (not included).

This adapter is used in conjunction with Intercomp's Kart Toe Plates or Kart Alignment System if the Kart has a 17mm or 5/8" direct spindle mount front end.

Wide-5 hub plate for Hub-Mounted, Corner Weight Scale.

5x5 hub plate for Hub-Mounted, Corner Weight Scale.

CNC machined billet aluminum housing with easy-to-read bubble display.

INCLUDES: 5/8" Adapter and Case

CNC machined billet aluminum housing with easy-to-read bubble display.

INCLUDES: 14/17mm Adapter and Case

.625 - 18UNF

14/17mm - 1.5

For SW500, SW520, SW650R1, and SW777 Scale Systems.

Includes One Green Cable.

SET OF FOUR

This single piece, aluminum, leveler is designed to fit any 15" scale pad with a 2.5" pad thickness. Enables the car to be rolled on & off the scale pad with little effort.

SET OF FOUR

This single piece, aluminum, leveler is designed to fit any 15" scale pad with a 4" pad thickness. Enables the car to be rolled on & off the scale pad with little effort.

Rechargeable 9 volt nicad battery for:

The industry's easiest to use and most compact lap timer at just 4"x2.5"x0.8"/100x6x20mm.

Includes: On-Board Receiver/Display Unit, In-Field Transmitter, Printer, and Carrying Case.

Race Car Management Software and Interface Cable Sold Separately.

Now you can check your bleeder valves with the same gauge that you use to set your tire pressures.

Bleeder Valve thread is 1/8th NPT.

Can be used with digital caster/camber gauges.

Wide-5

Steel machined wide five dust cover for magnesium hubs.  For use with caster/camber gauges that have magnetic adapters.

Steel machined Wide-5 dust cover for magnesium hubs. For use with caster/camber gauges that have magnetic adapters.

Tire & Brake tempuratures tell the story! Tire & Brake tempuratures are the best indicator of how a chassis is handling, but it is critical that this key information be gathered as rapidly as possible. Now you can record multiple tire and brake temperatures, recall the data from memory, or print out a copy for quick analysis.

Includes: Pyrometer/Timing Unit, Tire Probe, Printer, and Carrying Case

The first and most accurate, self-contained, digital, combination leak down, and compression tester. Repeatable accuracy for engine cylinder and fuel injector/barrel valve leak down percentages. Reads engine compression pressures to 400 PSI Locking regulator allows for incoming air pressure adjustment. Your intake air pressure and hose length do not affect your readings. Features:

Includes 14mm Leak Down Hose, 14mm Compression Hose and Case.  

14mm Hose for Intercomp's Leak Down/Compression Tester.

Female assembly hose for Intercomp's Leak Down/Compression Tester

Includes case

For SW500, SW520, SW650R1, and SW777 Scale Systems.

Includes One Black Cable.

12mm hose for Intercomp's Leak Down/Compresion Tester.

10mm hose for Intercomp's Leak Down/Compression tester.

System Includes:

• 10"x8"x2" (254x203x51mm) Billet Pads
• Cabled Indicator with Case
• 9-Volt Rechargeable Battery

Displays to one hundredth of a percent!

Featuring

Intercomp Introduces the Newest & Easiest Way to Weigh Your Kart!

• 400 lb (200 kg) Pad Capacity
• 1,600 lb (800 kg) System Capacity

• 4-bolt Load Cell Design
• Stores 100 Chassis Setups
• Baseline Setup Recall
• Center of Gravity Calculation
• User Selectable Display Modes
• Certified to 0.1% Accuracy
• RS232 Output
• Giant 0.5" Display Characters
• Backlit for Night Use

• 10"x10"x2" (254x254x61mm) Billet Pads
• Indicator with Storage Case
• 9-Volt Rechargeable Battery

For SW500, SW520, SW650R1, and SW777 Scale Systems.

Includes One White Cable.

Industry's only fully Digital Caster/Camber Gauge!

Indicates to 1/10 of a degree and has a +/- 20 degree caster/camber reading. Up to 10 times greater accuracy than traditional competitor's bubble gauges. Standard 9-volt battery gives up to 100 hours of operation. Lightweight, aluminum design, with auto shutoff and inclinometer mode for pinion and strut angles.

Standard features include

Can be used with most brands of caster/camber gauges.

Sprint Car 1.188 - 16UNF

Race Car Management Software Upgrade from v1.0

Bandolero/Small Ford Spindle Adapter .750 - 16UNF

Dual pad system with large readout is ideal for the serious racer. Used by ADHRA, AMA, FIM, IDBA, and most professional race organizations

Shocks are the most important part of your vehicles suspension and need to be maintained just like any other mechanical device that has valves, seals and oil. New and used shocks should be tested for performance characteristics.

FEATURES:

Thermal Printer for Wireless Scale Systems.  Operates 120/220 volt.

SW650, SW777, SW8.8k Scale System, Memory Pyrometer, Tire Pyrometer, or Memory Air Gauge to Computer Cable.

CLOSEOUT!! Compact, digital, parts scale.

Limited quantity, orders filled on a first come, first serve basis.

Torsion Bar Spline Adapter Set

Torsion Bar Spline Adapter Set

Torsion Bar Spline Adapter Set

Torsion Bar Spline Adapter Set

Torsion Bar Spline Adapter Set

Torsion Bar Spline Adapter Set

Set of 4 replacement Tire Chucks for Dryer/Purger.

120V Transformer

120V Transformer

Intercomp Racing T-Shirt.  100% cotton

Available in:

Small, Medium, Large, X-Large, and XX-Large

(Factory Certified)

This ultra quick, high accuracy, digital gauge is the choice of professionals in all types of motorsports.

(Factory Certified)

This ultra quick, high accuracy, digital gauge is the choice of professionals in all types of motorsports.

(Factory Certified)

This ultra quick, high accuracy, digital gauge is the choice of professionals in all types of motorsports. 

SET OF FOUR

Designed to fit any 15" scale pad with a 4" pad thickness. Enables the car to be rolled on & off the scale pad with little effort.  The external battery tray allows for easy access on wireless models.

6061 T6 Billet Aluminum Construction

SET OF FOUR

This single piece, aluminum, leveler is designed to fit any 15" scale pad with a 2.5" pad thickness. Enables the car to be rolled on & off the scale pad with little effort.  External battery tray allows for easy access on wireless scales.

6061 T6 Billet Aluminum Construction

Serial Cable for Scale or Pyrometer to Thermal Printer.

First fully adjustable, digital, Valve Spring Tester for rocker length and offset!

• 600lb/272kg Capacity
• Precision 5lb/kg Increments
• Brass Contact to Prevent Rocker Damage
• Fully Anodized Billet Aluminum Components
• Comfort Grip T-Handle for Improved Accuracy and Ease of Use
• Extremely Lightweight
• Infinite Adjustment and Peak Hold for Hard to Reach Areas
• 9-Volt Battery Operation
• Backlit for Night Use

Wide-5 ruler hub plate for Ruler Travel Bump Steer Gauge.

Wide-5 hub plate for Digital Travel Bump Steer Gauge.

This digital unit delivers unsurpassed accuracy via a digital controller, accomodating PSI, BAR, & Kg/Cm2 units of measure.

Rates standard and stacked coil-over setups!

• Rates coil-over and coil springs
• 6 inch Jack Travel
• 8 inch Digital Travel Indicator
• Checks shocks with coil-over springs to over 28 inches
• Includes 2 plates with 1/2" holes for shock mounting capabilities
• 2 pins with measuring capabilities to hold shocks in place

Torsion Bar Spline Adapter Set

• 2.000-48

Serial Cable - Lap Timer to Thermal Printer.

• Displays Setups to One-Hundredth of a Percent!
• Stores 100 Chassis Setups
• Baseline Setup Recall
• User Selectable Display Modes
• View Any Combination of Scale Pad Weight & Percentage
• Center of Gravity Calculation
• Target Tune Feature
• Certified to 0.1% Accuracy 

• Standard Rechargeable 9-volt Battery Operation
• RS232 Output
• Giant 0.5" Display Characters

• 1,500 lb (700 kg) Pad Capacity
• 6,000 lb (2,800 kg) System Capacity

• 15"x15"x2.5" (381x381x64mm) Billet Scale Pads
• 9-Volt Rechargeable Battery
• 2-Year Warranty

• Fully Integrated RFX Wireless Weighing Technology
• Encryption Ensures Secure Wireless Communication
• USB & RS232 Output
• Certified to 0.1% Accuracy

• 1,500 lb (700 kg) Pad Capacity
• 6,000 lb (2,800 kg) System Capacity

• Stores 100 Chassis Setups
• Baseline Setup Recall
• Center of Gravity Calculation
• User Selectable Display Modes
• Target Tune Feature
• Giant 0.5" Display Characters
• Backlit for Low-Lighting Conditions
• View Any Combination of Scale Pad Weight & Percentage

• 15"x15"x2.5" (381x381x64mm) Wireless RFX Billet Pads
• One-Touch Wireless Indicator with Case
• AA Alkaline Batteries
• 2-Year Warranty 

• Fully Integrated RFX Wireless Technology
• Encryption Ensures Secure Wireless Communication
• USB & RS232 Output
• Certified to 0.1% Accuracy 

• 1,500 lb (700 kg) Pad Capacity
• 6,000 lb (2,800 kg) System Capacity

• Stores 100 Chassis Setups
• Baseline Setup Recall
• Center of Gravity Calculation
• User Selectable Display Modes
• Target Tune Feature
• Giant 0.5" Display Characters
• Backlit Display

• 15"x15"x2.5" (381x381x64mm) Wireless RFX Billet Pads
• One-Touch Wireless Indicator with Case
• Pad Storage Case
• USB Cable
• Race Car Management Software
• AA Alkaline Batteries
• 2-Year Warranty

• 1,500 lb (700 kg) Pad Capacity
• 6,000 lb (2,800 kg) System Capacity

• Fully Integrated RFX Wireless Technology
• Encryption Ensures Secure Wireless Communication
• Certified to 0.1% Accuracy
• Custom Displays
• Intercomp's Field Proven RaceWeigh Software

• 15"x15"x2.5" (381x381x64mm) Wireless RFX Billet Pads
• Node for PDA
• PDA with Software
• Storage Case

• 1,500 lb (700 kg) Pad Capacity
• 6,000 lb (2,800 kg) System Capacity

• Fully Integrated RFX Wireless Technology
• Encryption Ensures Secure Wireless Communication
• Certified to 0.1% Accuracy
• Custom Displays
• Intercomp's Field Proven RaceWeigh Software

• 15"x15"x2.5" (381x381x64mm) Wireless RFX Billet Pads
• Node for PC
• Software for PC
• Storage Case

• 2,200 lb (1,000 kg) Pad Capacity
• 8,800 lb (4,000 kg) System Capacity

• Fully Integrated RFX Wireless Technology
• Encryption Ensures Secure Wireless Communication
• Certified to 0.1% Accuracy
• Custom Displays
• Intercomp's Field Proven RaceWeigh Software

• 15"x15"x4" (381x381x100mm) Wireless RFX Billet Pads
• Node for PC
• Software for PC
• Storage Case

 

• 2,200 lb (1,000 kg) Pad Capacity
• 8,800 lb (4,000 kg) System Capacity

• Fully Integrated RFX Wireless Technology
• Encryption Ensures Secure Wireless Communication
• Certified to 0.1% Accuracy
• Custom Displays
• Intercomp's Field Proven